Heil Sound PS EPC Cotton Ear Covers for Pro Set
PS EPC Cotton Ear Covers for Pro Set/Pro Set Plus/Pro Set Quiet Phone
Heil Sound PMS-6 Headset & boom mic, single-side, HC6
Heil Pro Micro PMS-6 "Single Side" - Heil Single Side with HC 6 Dynamic Element The Pro Micro Single Side is a very unique high performance single sided headset. This headset is outfitted with the HC-6 element and is designed for commercial broadcast applications, the -3dB points are fixed at 100 Hz and 12 kHz with sensitivity of -57 dB at 600 ohms output impedance (centered at 1 kHz.)The microphone audio for the Pro Micro series terminates into a 1/8” male plug while the head phone terminates into a 1/8” stereo with adaptor. To adjust the headset simply bend the stainless steel piece that is inside the black padded headband. Mic GainAdjust the mic gain while watching the ALC meter. Adjust so that the audio peaks just fill out the ALC scale and do not go beyond the ALC scale.SpeakerThe 706 speaker works all the time. To turn that off simply plug an empty 1/8” plug into the front headphone jack.VoxSet the Vox gain controls for proper activation.Carrier BalanceIf your rig has carrier balance it acts as a type of mic tone control. It is best to listen to yourself in another receiver as you transmit into a dummy load. You are actually moving the carrier + or - 200 Hz above or below the center of the filter network, which causes your microphone audio to change its tonal quality.The use of the AD-1 series mic adapters allow simple interface with popular transceiver inputs. The adapter is 6” long and has a 1/8” female input jack for the boomset microphone and a 1/4” female that is for the PTT (push to talk) line for the Heil foot switch or hand switch. The 1/4” stereo plug goes into the headphone jack on the transceiver front panel.All Heil Pro Micro Boomsets are shipped with foam windscreen that fits over the microphone. The windscreen does not change the frequency response, just the breath blasts directly into the microphone.
Heil Sound AD-1-I Headset adapter cable: Icom
Heil AD-1 Icom 8 Pin Adapter Cable AD-1 Microphone Adapters for Heil Boomsets By leaving the adapters plugged in your radio, you can move from transceiver to transceiver with the Pro Series Boomset without having to rewire the microphone for each individual radio. Features: All Heil Boomsets require the appropriate adapter to mate them to your particular model transceiver. Custom orders are available for other brands. A 1/4" female jack exits the radio connector for connections for a PTT switch or footswitch.
Heil Sound Pro Set iC Headset & boom mic, Rag-chew, IC
Heil Pro Set iC w/iC element Includes Special AD-1 Icom Cable. * Special version for pre (PRO) series Icom radios. Designed to meet the exacting standards of world-class Contest and DX operators, the Heil Sound Pro Set Series is the best-selling Boom Mic/Headset combo on the market! The Heil Sound Pro Set is a lightweight, versatile boom mic/headset designed for comfort, durability, and, above all, performance. The earpieces are full sized, with heavily-stuffed cushions for operator comfort during long operating stints. The ear pad covers are removable, for washing, and replacement pads are also available (see the "Parts" page). Besides sealing out noise passively, the Pro Set now includes Heil Sound's exclusive phase reversal technology, which allows the user to "move" the incoming signal by engaging the phase-reversal switch; this creates a unique spatial widening sound that can, in some situations, significantly improve copy in a tough DX pile-up. The earphone speakers in the Pro Set Series are 200-Ohm devices, with a -3 dB point at 8000 Hz. This combination reduces a lot of the hiss found in receiver audio stages. These speakers exhibit medium sensitivity, but they are easily driven by most rigs if you turn the AF Gain control up to about 2 o'clock. The Pro Set iC (PS iC) utilizes the Heil Sound "iC" condenser element specially designed by Heil Sound for compatibility with the low gain found on many Icom transceivers' mic amp stages. The PS iC is also shipped with the AD-1 iC adapter cable and each Pro Set is equipped with a windscreen for the microphone. The windscreen does not affect the frequency response of the microphone, and it is highly effective in minimizing breath blast while you're speaking. Take advantage of Heil Sound's years of engineering experience, and get yourself a Pro Set today!
Heil Sound PS Headset & boom mic, Rag-chew, HC6
Heil Pro Set 6 - Pro Set Boomset with Phase Reversal with new HC-6 Element Designed to meet the exacting standards of world-class Contest and DX operators, the Heil Sound Pro Set Series is the best-selling Boom Mic/Headset combo on the market! The Heil Sound Pro Set is a lightweight, versatile boom mic/headset designed for comfort, durability, and, above all, performance. The earpieces are full sized, with heavily-stuffed cushions for operator comfort during long operating stints. The ear pad covers are removable, for washing, and replacement pads are also available (see the "Parts" page). Besides sealing out noise passively, the Pro Set now includes Heil Sound's exclusive phase reversal technology, which allows the user to "move" the incoming signal by engaging the phase-reversal switch; this creates a unique spatial widening sound that can, in some situations, significantly improve copy in a tough DX pile-up. The earphone speakers in the Pro Set Series are 200-Ohm devices, with a -3 dB point at 8000 Hz. This combination reduces a lot of the hiss found in receiver audio stages. These speakers exhibit medium sensitivity, but they are easily driven by most rigs if you turn the AF Gain control up to about 2 o'clock. Each Pro Set is equipped with a windscreen for the microphone. The windscreen does not affect the frequency response of the microphone, and it is highly effective in minimizing breath blast while you're speaking. Take advantage of Heil Sound's years of engineering experience, and get yourself a Pro Set today!
Heil Sound AD-1-K8 Headset adapter: Kenwood 8-pin round
Heil AD-1 Kenwood/Alinco 8 Pin Adapter Cable AD-1 Microphone Adapters for Heil BoomsetsBy leaving the adapters plugged in your radio, you can move from transceiver to transceiver with the Pro Series Boomset without having to rewire the microphone for each individual radio.Features:All Heil Boomsets require the appropriate adapter to mate them to your particular model transceiver.Custom orders are available for other brands.A 1/4" female jack exits the radio connector for connections for a PTT switch or footswitch.
Heil Sound AD-1-ICM Headset adapter: Icom modular w/o cap
Heil AD-1 Icom Modular w/o cap No capacitor. Use only with our 'iC' electret condenser elements. This has NO capacitor thus allowing the control voltage to reach the 'iC' element. AD-1 Microphone Adapters for Heil BoomsetsBy leaving the adapters plugged in your radio, you can move from transceiver to transceiver with the Pro Series Boomset without having to rewire the microphone for each individual radio.Features:All Heil Boomsets require the appropriate adapter to mate them to your particular model transceiver.Custom orders are available for other brands.A 1/4" female jack exits the radio connector for connections for a PTT switch or footswitch.
Heil Sound PR-781G Microphone: broadcast, hi-end ham radios
PR 781 Dynamic Desk microphone for Elite transceivers. For amateur radio, the correct CC-1 XLR cable is required to interface with a transceiver.
Heil Sound EP PSP Replacement ear pads for Pro Set Plus
Replacement ear pads for Pro Set Plus (pair)
Heil Sound AD-1-Y8 Headset adapter cable: Yaesu 8-pin round
Heil AD-1 Yaesu 8 Pin Adapter Cable AD-1 Microphone Adapters for Heil Boomsets By leaving the adapters plugged in your radio, you can move from transceiver to transceiver with the Pro Series Boomset without having to rewire the microphone for each individual radio. Features: All Heil Boomsets require the appropriate adapter to mate them to your particular model transceiver. Custom orders are available for other brands. A 1/4" female jack exits the radio connector for connections for a PTT switch or footswitch.
Heil Sound PS 7 Red Headset & boom mic
Heil Pro Set 7 - Headset & boom mic - Red. **Also available in Black, Pink, and Blue!**Meet the new boss!The most comfortable wearing headset - ever.Adjustable stainless headband.Special designed foam gel ear pads provide 26 dB PNR reduction of outside noiseCotton cloth "booties" to cover ear pads40 mil high response speakers producing extreme voicearticulationAcoustically tuned speaker enclosure-3 dB points set at 80Hz to 12kHzSpeaker balance control adjusts level between the two speakersFull stereo, two channel reception. Perfect for Dual Watch receiving systemsMilitary spec cable system using 6 pin mini-XLR and fiber reinforced cableConnects to standard Heil headphone adaptersDetachable coil cable with comfortable "Soft Touch" in line, 2" diameter P.T.T.1" thick, 6 section foam headband for maximum comfortInterchangeable microphone element. HC 7 articulate dynamic OR Heil electret iC condenserHeil EXCLUSIVE Speaker Phase reversal helps to "dig out" the weak signals
Heil Sound PS EP Replacement ear pads for Pro Set
Heil Pro Set Ear Pads (Set of 2 ear pads) This replaces the leather pads AND the foam inserts for one pair of Pro Set headset speakers. Fits all Pro Set models.
heil sound sm1 spider shockmount for pr20 microphone
Heil Shock Mount for 5/8 inch X 27 threaded stand or boom. For use with the Heil Sound GM, HM-10, iCM, PR-20 and similar body shapesUPC NO:663647973986 SKU:ADIB0018TC7GC
Heil Sound EP BM BLA Replacement ear pads for BM-10, black
HEIL EAR PADS(BM-10 REPLACEMENT) BLACK Foam Ear Pads (Pair)
Heil Sound HEIL BAG1 Travel bag for Pro-set headsets
Heil Bag 1 fits Pro Set or Pro Set Plus headsetsThe perfect place for your next DxPedition, plane ride or protection against the dog.Exterior Features:Quality constructed leatherette carrying caseZipper closureEmbossed Heil Sound LogoSturdy handleInterior Features:Velcro securing strapMesh storage pouch
Heil PR31BW Diaphragm Microphone
The Heil PR 31 BW was a suggestion of Bob Workman, FOH engineer for Charlie Daniels, who uses Heil microphones exclusively. Bob uses the Heil PR 30 for just about every application but it was too large physically to fit in and around the drum kit so Bob suggested Heil "cut it in half," and that's exactly what they did-and the Heil PR 31 BW was born-a 4" version of the PR 30 that exhibits all specs of the full-size PR 30. It has the same great frequency response, same wonderful front pattern, and the incredible -40 dB of rear and side rejection, which is perfect for using the PR 31 BW as an "underhead" microphone for cymbals. Placing a microphone under the cymbal has never been successful because the microphone hears everything around it. With the -40 dB of rear and side rejection of the PR 31 BW, the microphone does not hear anything but what it is point towards-in this case, the cymbal and nothing from the toms or other sounds close by. Using a right-angle connector and the Heil Sound HH-1 rim mount, the PR 31BW is the perfect low-profile answer for toms. The PR 31 BW also works great in front of a guitar cabinet, brass, and saxophone, inside a Leslie speaker, and is perfect for acoustic pianos. It's a go-to microphone for just about everything, including vocals. This incredible little bombshell is rightfully named, the HEIL PR 31 BW in honor and thanks to Bob Workman
Heil Sound CC-1-XLR-Y-BAL Mic adapter cable, XLR bal.: Yaesu 8-pin
Heil Sound CC-1 XLR Yaesu 8 Pin Cable for FT-950 (also works with FT-2000, FT-5000, and FT-9000). The CC-1 XLR K, Y & I (Adapter Cables) are also used to interface your Heil microphone with your favorite 8-pin Kenwood, Yaesu or Icom transceiver. This cable is used for our Classic Pro, GM Pro and Heritage microphones that have industry standard 3-pin balanced XLR output connectors, for use with unbalanced microphone inputs using 8-pin Foster connectors. ALL CC-1 cables also use the commercial grade HEIL 8 pin MICROPHONE connectors (patent pending) with dual exit cable clamps and much heavier than the normal CB type connector the industry has been forced to use for decades. All CC-1 cables are made using the commercial audio 'Heilwire'. The PTT d. c. control lines are located OUTSIDE of the 100% silver braid thus helping to reduce RFI and noise environments from your shielded audio input circuits If you have several brands of transceivers, you can move your Heil microphone quickly from transceiver to transceiver without having to rewire any connectors. Features: All Heil Microphones require the appropriate adapter to mate them to your particular model transceiver. A 1/4" female connector exits the radio connector which allows you to connect our footswitch or handswitch to control the PTT lines of the transceiver. Specifications: The CC-1 XLR K, Y & I Series adapters are only available in an 8 pin Foster style connector for Kenwood, Yaesu & Icom and are used only for the Heil Pro Line microphones. Additionally, these adapters convert the microphone's balanced output signal to an unbalanced signal suitable for your transceiver's microphone input.
Heil Sound BM-BOOM-CLIP Boom clip for BM-10
Heil BM-10 Boom Mic Clip Plastic boom clip for BM-5 and BM-10
Heil Sound CC-1-XLR-I Mic adapter cable, XLR: Icom 8-pin round
Heil Sound CC-1 XLR Icom 8 Pin Cable The CC-1 XLR K, Y & I (Adapter Cables) are also used to interface your Heil microphone with your favorite 8-pin Kenwood, Yaesu or Icom transceiver. This cable is used for our Classic Pro, GM Pro and Heritage microphones that have industry standard 3-pin balanced XLR output connectors, for use with unbalanced microphone inputs using 8-pin Foster connectors. ALL CC-1 cables also use the commercial grade HEIL 8 pin MICROPHONE connectors (patent pending) with dual exit cable clamps and much heavier than the normal CB type connector the industry has been forced to use for decades. All CC-1 cables are made using the commercial audio 'Heilwire'. The PTT d. c. control lines are located OUTSIDE of the 100% silver braid thus helping to reduce RFI and noise environments from your shielded audio input circuits If you have several brands of transceivers, you can move your Heil microphone quickly from transceiver to transceiver without having to rewire any connectors. Features: All Heil Microphones require the appropriate adapter to mate them to your particular model transceiver. A 1/4" female connector exits the radio connector which allows you to connect our footswitch or handswitch to control the PTT lines of the transceiver. Specifications: The CC-1 XLR K, Y & I Series adapters are only available in an 8 pin Foster style connector for Kenwood, Yaesu & Icom and are used only for the Heil Pro Line microphones. Additionally, these adapters convert the microphone's balanced output signal to an unbalanced signal suitable for your transceiver's microphone input.
Heil Sound WSPS Micphone windscreen for Pro Set
Heil Foam Windscreen for Pro Set and Pro Micro Boomsets
Heil Sound HEILWIRE 10 Microphone cable, 4-cond. shielded 10ft
10ft Heil Wire Microphone Cable (Shielded 2 conductor Audio Cable and 2 conductor Control Cable) For years, the amateur radio industry has been forced to use audio cable built for some other purpose than connecting a. c. and d. c. voltages between microphones and transmitters. Until the past few years, this has not been a big problem but with the recent focus on high quality audio and the need to interface much more than a simple microphone, the need for higher quality cable has grown. But the proper cable just simply doesn't exist. Until now. Heil Sound, has once again answered the problem by designing and producing "Heilwire" - a specialized cable specifically for use in interfacing balanced audio lines from a professional audio mixer into the transmitter input. Along with this is the ability to carry the d. c. control lines either from a push to talk circuit or a computer keying system. The key to this new wire is to reduce the capacitive coupling between these two signals and shield the sensitive audio lines from the outside r. f. environment to reduce interference that the transmitter may create. "HEILWIRE" contains two 18 gauge audio leads residing in a 100% silver braided shield. Not the usual 40% spiral wrap or aluminum foil that has been the used in this market for years, but a true 100% silver braid that shields those very sensitive balanced audio lines from the outside world. Along side of this shield is another pair of 18 gauge control wires that can carry the push to talk circuits and keep the d. c. components totally away from the a. c. audio signals. The outer jacket is a very flexible p. v. c. jacket that was designed to fit - exactly into the cable clamp system of the popular 8 pin Foster plug used by the majority of amateur radio transmitters. No extra "fill" grommets or heat shrink necessary to make the Foster clamp work. "HEILWIRE" fits perfectly and brings a new direction to audio cable systems in the amateur radio as well as commercial broadcast industries.
