SunFounder Motor Driver Shield for Arduino and Raspberry Pi
Introduction of L293DWith a 16-pin DIP package, L293D integrates a bipolar H-bridge circuit internally. The bipolar PWM method has many advantages: continuous current, four-quadrant operation of motors, smoothness during low speed, micro-vibration currents when the motor stops (which as dynamic lubricator can eliminate static friction during the motor forward-inverse rotation), etc. L293D generates enable signals by internal logic circuit. The input of H-bridge circuit can be used to define the direction of the motor rotation when the enable signals, for PWM. Besides, it integrates two H-bridge circuits onto one chip, which means one chip can control two motors simultaneously. Each motor needs three kinds of control signals: EN12, IN1, and IN2. Within, EN12 are enable signals, when IN1 and IN2, motor rotation direction ones. When IN1 and IN2 are 1 and 0 respectively, the motor rotates forward; or else, it rotates inversely. Connect of the PWM pins with pin EN12 and then you can change the rotational speed of the motor by adjusting the duty cycle of PWM. Connect one of I/O pins with pin IN1 and IN2 with the inverter 74HC14, so as to control the forward and reverse rotation of the motor. A shield to drive DC motors, stepping motors and servos; just plug it onto a Uno board (Arduino, SunFounder, or other compatibles) for useUse L293D to drive motors: capable of driving two lines of DC motors at the same time; use ULN2003: capable of driving one line of stepping motors; use a 5V supply: capable of driving 4 lines of servosApplicationThe module can be used as the driver board for robots and smart cars. Component List 1 * Motor Driver Shield 1 * 4-Pin anti-reverse cableNote: The shield itself does not support any functions; it needs to be plugged onto a Uno board for normal use. For protection of the shield, PLEASE use an EXTERNAL power supply!
SunFounder Light seeking Sensor Module for Arduino and Raspberry Pi
IntroductionThe Light Sensor module can be used on a smart car for the experiment about light seeking. Since the resistance of a photoresistor decreases with strong light, the car can be controlled to move based on the resistance change, that is, to seek for the light and follow it. Also the light intensity can be reflected by the LED bar on the module. A light sensor module consisting of a photoresistor, LED bar, 74HC595, and resistor, that can detect light and reflect the intensity by the LED bar on itThe on and off of the LED bar is controlled by 74HC595; the photoresistor is connected to pin A ApplicationAuto light-seeking smart car Component List 1 * Lightseeking module
SunFounder Analog Temperature Sensor Module for Arduino and Raspberry Pi
IntroductionAn analog temperature sensor module that consists of an NTC thermistor, resistor, capacitor in a circuit. The NTC thermistor is very sensitive to ambient temperature and hence widely used to detect the temperature, with a wide range of temperature measurementThe threshold of temperature detection can be adjusted by rotating the potentiometer. When the temperature exceeds the threshold, D0 outputs low and the corresponding LED will light up. A 4-pin anti-reverse cable included. Application The module can be applied to temperature detection, temperature control sensor, and ambient temperature detection, as well as temperature alarm. Component List 1 x Analog temperature sensor module 1 x 4-Pin anti-reverse cable
SunFounder 7-Color Auto-flash LED Module for Arduino and Raspberry Pi
ApplicationMainly to decorateComponent List 1 x 7-color auto-flash LED module1 x 3-Pin anti-reverse cable
SunFounder Project Super Starter Kit for Arduino UNO R3 Mega2560 Mega328 Nano-OEM
Feature: The user manual of the Sun Founder Superkit V 2.0 for Arduino provided will be of larger size than the previous one, with more details at the same time. Much clearer Fritzing breadboard images and schematic diagrams are given. A bigger case for the package, inside which are divided into 8 grids for storing the components by category after you finish the experiment. The UNO R3 board is NOT included 19 Projects for beginners: Lesson 1 Blinking LED Lesson 2 Controlling LED by Button Lesson 3 Controlling LED by PWM Lesson 4 Controlling LED by Potentiometer Lesson 5 LED Flowing Lights Lesson 6 RGB LED Lesson 7 DC Motor Control Lesson 8 LCD1602 Lesson 9 Serial Monitor Lesson 10 7-Segment Display Lesson 11 74HC595 Lesson 12 Dot-matrix Display Lesson 13 NE555 Timer Lesson 14 Rotary Encoder Lesson 15 ADXL335 Lesson 16 Simple Creation - Light Alarm Lesson 17 Simple Creation - Traffic Light Lesson 18 Simple Creation - Digital Dice Lesson 19 Simple Creation - Small Fan Package included: 1x RGB 1x Project Box 40x Pin Header 1x Timer 555 2x Optocoupler 4N35 2x Shift Resister 74HC595N 1x H-Bridge L293D 1x Accelerometer ADXL335 1x Rotary Encoder 5x Push-Button small 8x Resistor 220 Ohm 4x Resistor 1k Ohm 4x Resistor 10k Ohm 1x Resistor 1M Ohm 1x Resistor 5.1M Ohm 1x Switch 1x Trim Pot - 50k 1x LCD Character Display 16x2 1x Dot Matrix Display 8x8 2x 7-Segment Character Display 1x DC Motor 16x LED red 2x LED white 2x LED green 2x LED yellow 2x Transistor NPN 2x Transistor PNP 4x Capacitor Ceramic 100nF 4x Capacitor Ceramic 10nF 2x Diode Rectifier 1x Breadboard 1x USB Cable 65x Male to Male Jumper Wires 20X Female to Male Dupont wires 1x Piezo Buzzer 1x fan 1x Booklet
SunFounder IIC I2C TWI Serial 2004 20x4 LCD Module Shield for Arduino R3 Mega2560
With the LCD shield, you can display whatever you want by programming for Arduino board or Raspberry Pi. Therefore, this is a perfect choice to make your project more interesting and vivid! Specification: Display: 4 lines x 20 characters Backlight: Blue with white character color LCD controller: HD44780 Pin Definition: VCC/ GND/SDL and SCA Contrast Adjust: Potentiometer Backlight Adjust: Jumper Default Address: 0x27, 0x3F Working Voltage: 5V Package: 1 x blue 20x4 2004 lcd display + I2C serial interface With IIC/I2C interface, it only takes two I/O port thus saving more for other usages. You can adjust the contrast by the potentiometer at its back. If you don’t want the backlight, you can also unplug the jumper cap at the LCD back. This is a high-quality I2C LCD 2004 display. It's in elegant blue with white contents displayed. Can display 4 rows with 20 characters for each.
SunFounder SD Card Module Slot Socket Reader for Arudino UNO R3 Mega 2560 Nano
1. This SD Card module can make your SD application more easier and simple. 2. It is easily interfaced as a peripheral to your arduino sensor shield module. 3. Through programming, you can read and write to the SD card using your arduino. A. Can be used for SD Card more eaisly, such as for MP3 Player, MCU/ARM system control. B. All SD SPI pins output, MOSI, SCK, MISO and CS. C. Support 5V/ 3.3V input Package Content: 1 X Sun Founder SD Card Module Slot Socket Reader for Arduino
SunFounder Mini USB Nano V4.0 ATmega328P 5V Micro Controller Board for Arduino Compatible
Sunfounder Nano is created by the purpose of repairing a defect on the Arduino Nano, it is the same in general and can replace the Arduino Nano 3.0. The Sunfounder Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3. x) or ATmega168 (Arduino Nano 2. x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. More details can be found at http: //www. sunfounder. com/index. php? =downloadscs & a=Manualdetails & id=79 & name= Microcontroller: Atmel ATmega168 or ATmega328 Operating Voltage (logic level): 5 V Input Voltage (recommended): 7-12 V Input Voltage (limits): 6-20 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 8 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader SRAM: 1 KB (ATmega168) or 2 KB (ATmega328) EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328) Clock Speed: 16 MHz Dimensions: 0.73" x 1.70" Length: 45 mm Width: 18 mm Weigth: 5 g
SunFounder RAB Holder Raspberry Pi Breadboard Holder 5 in 1 Base Plate with Rubber Feet with 120pcs Breadboard Jumper Wires
WIDE-RANGE COMPATIBLITY- This base plate case is compatible with Arduino R3, Mega2560 and Raspberry Pi 4B/3/2/B+, Pi zero as well as working with both 400 and 830 points breadboards. SUPERIORLY DESIGNED SLOTS- The slots are specially designed for TF cards, HDMI and USB cords to be inserted without hindering the power connection. WELL-CRAFTED DESIGN- The RAB Holder has a customized, sleek design that is attractive and is more comfortable to touch while working with it. 120pcs Dupont Wires: 40 male-male, 40 male-female, 40 female-female. 0.127 mm, 36 AWG/ single root, 20cm (8inch) /axis; Standard 2.54 mm headers and sockets. The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers. Made of high-grade copper wire material for safe and durable to use.
raspberry pi 10 inch touch screen sunfounder 10.1" hdmi 1280x800 ips lcd touchscreen for rpi 3 model b+ 3b 2b lattepanda beagle bone
Introduction This SunFounder Touch Screen is a 10-point IPS touch screen in a 10.1 '' big size and with a high resolution of 1280x800, bringing you perfect visual experience. It works with various operating systems including Raspbian, Ubuntu, Ubuntu Mate, Windows, Android, and Chrome OS. Package Included 1 x 10.1 '' IPS Touch Screen 7 x M 2.5 x 14.4 Copper Standoff 2 x M 2.5 x 22 Copper Standoff 1 x HDMI Cable 1 x Micro USB Cable 1 x USB Touch Screen Cable UPC NO: 606034416819 SKU: ADIB0776VNW9C
SunFounder Raspberry Pi 4 Display Touchscreen 7 Inch HDMI 1024×600 USB IPS LCD Screen Display Monitor for Raspberry Pi 4 3 Model B, 2 Model B, and 1 Model B+, Windows Capacitive Touch Screen
HD VISUAL ENJOYMENT: SunFounder RPi touchscreen with HD 1024x600 resolution, 16.7M (8bit) color numbers give high color restore display. Rectangular ratio 16:9 display format conversion. IPS 170° full wide viewing angle gives you a crystal-clear viewing experience of all your content. MULTIPLE APPLICATION: Supports Raspbian/Win7/Win8/Win10 (Plug and play), Android/Linux (need to be configured first). And you can download Installation Manual for Raspberry Pi from the selling page. ( Note: the HDMI-Micro HDMI cable especially for Raspberry Pi 4, HDMI-HDMI cable for Raspberry Pi 3)LOW COMSUMPTION:Low power consumption and have a good effect connect with windows computer, no trouble with installing drivers for various systems. WIDE TOUCH AREA: The module size with 165.30 (W) *121 (H) * 7.75 (T), and the Active area is 154.21 (mm) * 85.92 (mm). Most of the screens on the market will have this touch problems if the software is not adjusted, but this small hdmi screen no worries to reach the side of the screen. PLUG and PLAY: Equip with Micro USB and HDMI port support. Connect the screen to device via HDMI interface and power it via USB. To achieve touch function powered by USB, do not require power cord and drive-free.
