47020 - AIR DUSTER AEROSOL 284G
MFR. No.: 47020 STOCK No.: QPA-1448AA
High strength Silver Epoxy, Electrically Conductive for microwave, EMI & FRI shielding assembly & PCB, electronic component manufacturing & Repair 904
- PRODUCT DESCRIPTION:
AA-DUCT 904 is a single component, heat curing, conductive epoxy that was designed for ease in handling. This high performance conductive epoxy cures quickly at elevated temperatures making it ideally suited for rapid processing and assembly.
AA-DUCT 904 offers excellent mechanical, electrical, and physical properties at continuous operating temperatures up to 175°C. This versatile silver conductive adhesive can be used for chip bonding in micro and opto-electronic hybrid circuit fabrication.
AA-DUCT 904 has also been used in microwave applications for EMI and FRI shielding, for assembly and repair of circuit boards and electronic component manufacturing.
AA-DUCT 904 is a smooth, soft paste that can be applied by hand application, automatic dispensers, screen-printing, transfer or stamping techniques. It is available in both a lower and higher viscosity grade for use in a variety of dispensing equipment and application techniques.
- CURED PROPERTIES:
Hardness, Shore D 83
- PRODUCT PROPERTIES:
Appearance Silver
Cure Type Heat cure
Benefits:
+ High strength
+ Excellent mechanical, electrical properties
Substrates: Excellent choice for Integrated Circuits, aluminum, copper, magnesium, steel, bronze, nickel, ceramic, glass,
phenolic and G-10 epoxy glass boards.
- CURE SCHEDULE:
2 hours @ 125°C
1 hour @ 150°C
1/2 hours @ 175°C
- UNCURED PROPERTIES:
Viscosity @ 25 °C cps: 200,000
Shelf life: 6 Months
Density: 3.6
- THERMAL PROPERTIES:
Thermal Conductivity, btu/hr/ft2/°F/in 16.1
Coefficient of Thermal Expansion 60x 10^-6 (in/in) C
Operating Temperature:
+ -55°C to +175°C
+ Intermit. to 325
- ELECTRICAL PROPERTIES:
Volume Resistivity ohm. cm 0.001
- NASA OUTGASSING RESULTS:
TML (Total Mass Loss) % 0.38
CVCM (Collected Volatile Condensable Materials) % 0.01
WVR (Water Vapor Recovery) % 0.07
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
Call (888) 522-6742 for more information.
This epoxy can be supplied in various different packages.
Super Electrically Conductive Silver Epoxy For Microwave EMI & RFI, Wave Guides, PCB, IC, Electronic Modules, Flat Cable, One Part, 905-100gm
- PRODUCT DESCRIPTION:
AA-DUCT 905 is a single component epoxy, formulated with pure silver powder combined with organic binders and solvents to produce electrically conductive paths, films or patterns over non-conductive substrates.
AA-DUCT 905 shows slight settling when stored for a long period of time, no caking and will re disperse to a smooth homogeneous state.
AA-DUCT 905 formulation produces electrically conductive paths on a wide variety of surfaces including plastics, rubber, cloth, thermoplastic, paper, wood and many others.
AA-DUCT 905 designed for use in diversified applications as microwave EMI & RFI shielding, in the assembly or repair of printed circuit boards, wave-guides, electronic modules, flat cable, static shielding, connections, and circuitry. This Epoxy is designed for screening and micro product adhesion applications.
- PRODUCT PROPERTIES:
Appearance : Silver
Cure Type: Heat cure
Benefits:
• High strength
• Perfect bond
• EMI & RFI shielding
• Wave guides
Substrates:
• Integrated Circuits
• Aluminum
• Copper
• Magnesium
• Steel
• Bronze
• Nickel
• Kovar
• Ceramic
• Glass
• Phenolic
• G-10 epoxy glass boards.
Catalyst: Anhydride
Hardness, Shore D: 83
- AVAILABILITY:
This epoxy can be supplied in many different packages.
CALL (888) 522-6742 for more informations.
High Strength Epoxy Adhesive, Perfect Bond Glue For Printed Circuit Boards, Wave Guides, Electronic Modules, Flat Cable, Static, EMI & RFI Shielding,
- PRODUCT DESCRIPTION:
AA-DUCT CG2 is a single component epoxy, formulated with silver coated ceramic that results in lower material costs without adversely sacrificing the properties obtained with a pure silver formulation. This concept opens the door to a wide range of applications previously prohibited by the much higher cost of Conventional silver conductive.
AA-DUCT CG2 Formulated with Silver coated ceramic power combined with organic binders and solvents to produce electrically conductive paths, films or patterns over non-conductive substrates.
AA-DUCT CG2 formulation produces electrically conductive paths on a wide variety of surfaces including plastics, rubber, cloth, thermoplastic, paper, wood and many others.
AA-DUCT CG2 designed for use in diversified applications as microwave EMI & RFI shielding, in the assembly or repair of printed circuit boards, waveguides, electronic modules, flat cable, static shielding, connections, and circuitry.
- GENERAL INFORMATION:
Appearance: Silver
Coated ceramic %Silver coated ceramic : 76
Cure Type: Heat cure
Benefits:
- High strength
- Perfect bond
- EMI & RFI shielding
- Wave guides
Substrates: Excellent choice for the Integrated Circuits, aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards.
Catalyst: Anhydride
- CURED PROPERTIES:
Sheet Resistivity:
1 Set of Silicone Useful Nonslip Creative Red Wine Glass Markers Wine Glass Clips Wine Charms Durable Reusable Convenient Cup Clips Tag Clips Glass Cl
DescriptionAre you looking for creative and fashionable cup signs? If yes, then you can not miss these products. They can meet your needs for decorating cups and reminding you which one is your cup on dining table. Come and take them home!Features-Material: Silicone.-Size: About 2.00X1.50X1.00cm / 0.79X0.59X0.39inch.-Help clearly identify guests' wine glasses at a glance at parties.-These markers will identify each wine glasses easily, easy to use.-These simple wine markers are good gifts for family and friends.-Decorate your wine glass and remind you which one is your cup.-Suitable for for restaurants, parties, KTV, cocktail parties, bars, etc.12 x cup markers
3.5mm Male AUX Audio Plug Jack To USB 2.0 Female Converter Cable Cord for Car Mp3 (White)
DescriptionThe AUX of the car interface must read U disk function(AUX decoding function), that it can use this kind of line AUX interface, some without AUX decoding function, use with MP3 only. U disk cannot have non music files, U disk inside can not have other files and do not create a folder, only MP3 format songs use.Feature- Color: White- Materials: PVC and Copper clad steel wire- Length: 18cm- Line 3.5 mm plug connected to the car’s AUX interface, USB interface to the U disk.- Pure and clean music sound quality / for vehicle navigation, car audio, anti-jamming, good signal.- Achieve automatic playback USB flash drive songs.- Delicate and light, easy to carry, use anytime, anywhere.- Please make sure your device has mp3 decoding function, you can read mp3 files from the U disk.1 x 3.5mm Male AUX Audio Plug Jack To USB 2.0 Female Converter Cable Cord for Car Mp3 (White)
Rigid Laminating, Sealing & Bonding Applications, Good Wetting, Great Mechanical & Electrical Properties, Medium Viscosity Epoxy Adhesive 2103, 2.5gm
- PRODUCT DESCRIPTION:
AA-BOND 2103 is a clear, near transparent, medium viscosity epoxy adhesive formulation developed for rigid laminating, sealing and bonding applications where the combination of good wetting and improved mechanical electrical properties is required. AA-BOND 2103 is two-part liquid epoxy adhesive contains no solvents and is easy to mix, use and apply at room temperature.
AA-BOND 2103 develops strong, rigid, high performance bonds to itself and to ceramics, glass and glass fabrics, metals, laminates and other composite materials, forestry and masonry products, and to most rigid plastics.
AA-BOND 2103 is an effective electrical insulator, and further provides excellent resistance to weather, galvanic action, vapors, JP4 fuel, gasoline, lubricants and other petroleum products, mild acids and alkalis, salts, and other organic and inorganic compounds.
- GENERAL PROPERTIES:
Appearance: Slight haze/Clear
Cure Type: Room temperature or Heat Cure
- Benefits:
Good wetting
Great mechanical properties
Great electrical properties
Solvent free
Easy mix and apply
Mix Ratio by weight 100:25 / Resin:Hardener
- Substrates:
Ceramics, glass to glass, fabrics, metals, laminates and other composite materials
- Operating Temperature: 60 to 125 °C
- UNCURED PROPERTIES:
Specific Gravity 1.2
Reactive solids contents, % 100
Pot Life 20 minutes
- CURE SCHEDULE:
4 hours at 65°C
24 hours at 25°C
- MISC PROPERTIES:
Volume Resistivity 6.00e+13 ohm-cm
Dielectric Constant 4.1Dielectric Strength 420 kV/in
Hardness, Shore D 85
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
CALL (888) 522-6742 for more information.
High Impact Adhesive, Two Part Epoxy, Medium Viscosity, AA-BOND 2135, 2.5gm kit
This is a medium viscosity epoxy adhesive recommended for bonding, laminating, sealing, and structural repair applications where easy mixing and good wetting combined with high impact strength properties are required. This superior, two-part adhesive is easily mixed and handled at room temperature, and develops strong, tough, high performance bonds to metals, ceramics, wood, concrete, phenolics, polyesters, epoxies, many urethanes and other plastics, and to many other materials. Fully cured this product is a tough, durable, electrically insulating adhesive with excellent mechanical, impact and shock resistance properties. In addition, it provides good resistance to gases, vapors, weather, water, petroleum solvents, anti-icing fluids, salt solutions, many mild acids and alkalis, and many other organic materials.
1280pcs 5% 0.125W 0805 SMD Resistor 64 Values 0ohm-10Mohm Assortment Kit
Feature: General purpose resistor with 1280pcs. High precision and stability. Automatic insertion is applicable. Each value is clearly marked. Specification: Material: PlasticModel: 0805 whole seriesAllowable deviation: & plusmn ; 5%Rated power: 0.125 (W) Various SMD resistance (unit: & Omega ; ): 0ohm-10Mohm64 values (each type for 20pcs): 0ohm, 2.2 ohm,;; 4.7 ohm, 5.6 ohm, 7.5 ohm, 8.2 ohm, 10ohm, 15ohm, 22ohm, 27ohm, 33ohm, 39ohm, 47ohm, 56ohm, 68ohm, 75ohm, 82ohm, 100ohm, 120ohm, 150ohm, 180ohm, 220ohm, 270ohm, 330ohm, 390ohm, 470ohm, 510ohm, 680ohm, 820ohm, 1Kohm, 1.5K ohm, 2.2K ohm, 3.3K ohm, 3.9K ohm, 4.7K ohm, 5.6K ohm,;; 6.8K ohm, 7.5K ohm, 8.2K ohm, 10Kohm, 15Kohm, 22Kohm, 33Kohm, 39Kohm, 47Kohm, 56Kohm, 68Kohm, 75Kohm, 82Kohm, 100Kohm, 150Kohm, 180Kohm, 220Kohm, 330Kohm, 470Kohm, 560Kohm, 680Kohm, 1Mohm, 1.5M ohm, 2Mohm, 3.3M ohm, 4.7M ohm, 5.6M ohm, 10MohmNotice: As a result of large and cumbersome jobs, sometimes the individual resistor value is duplicate or missing, please understand. Package includes: 1280 x Resistor (64 types);
Clear Epoxy, High Impact, Low Viscosity Adhesive for Fiber Optic Assembly, Small Potting & Sealing Applications, Multimode & Single Mode Connectors, 2
- PRODUCT DESCRIPTION:
AA-BOND F113 is an Optically Clear, low viscosity , High impact epoxy adhesives developed for bonding and small volume potting of plastic or glass optical fibers, lenses and prisms, LED displays, and other optical components.
AA-BOND F113 is recommended for laminating, bonding, and sealing applications where excellent wetting, good pot life and improved impact strength properties are required.
AA-BOND F113 is two parts adhesive easily mixed and cured at room temperature and develops strong bond to glass and glass fibers, ceramics, many metals and most rigid plastics.
AA-BOND F113 bonds offer resistance to mechanical impact and thermal shock, and is also resistant to weather, water, gases and vapors, petroleum products, and mild acids and alkalis.
- GENERAL PROPERTIES:
Appearance: Clear
Components: 2 component - requires mixing
Mix Ratio by weight: 100:30 / Resin:Hardener
Benefits: Low viscosity
Thermal shock and impact resistant
Low stress connections
Cure Type: Room temperature or Heat Cure
Operating Temperature: -60 to 120 °C
Typical Applications: Fiber optic assembly, multimode and single mode connectors, small potting and sealing applications
- UNCURED PROPERTIES:
Viscosity @ 25 °C: 175
Thixotropic Index: 1.0
Specific Gravity: 1.23
Pot Life: 1.5 hours
- CURE SCHEDULE:
24 hours @ 25°C
1-2 hours @ 65°C
- CURED PROPERTIES:
Coefficient of Thermal Expansion, cm/cm/ºC: 6.20×10+01
Glass Transition Temperature (Tg), ultimate, °C: 102
Hardness, Shore D: 86
Refractive Index: 1.51
Water Absorption , after 24 hours saturation, %: 0.07
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
Call (888) 522-6742 for more information.
Metal Repair Epoxy Adhesive, Steel filled, High Performance, AA-BOND FS313, 5 gm pouch
PRODUCT DESCRIPTION:
This Product is steel epoxy, tooling resin features a highly filled, low viscosity composition for low shrinkage,can be easily drilled, tapped, polished, milled, sawed, or turned on a lathe, with conventional metal-working tools. This unique resin system is recommended for the fabrication of metal and vacuum form molds, hammer forms, drop hammer dies, foundry patterns, master molds, core filling, draw and stretch dies, lay-up molds, etc. Easy mix pre-measured pouch. Simple mix and use without any mess.
High Strength Epoxy Adhesive, Perfect Bond Glue For Printed Circuit Boards, Wave Guides, Electronic Modules, Flat Cable, Static, EMI & RFI Shielding,
- PRODUCT DESCRIPTION:
AA-DUCT CG2 is a single component epoxy, formulated with silver coated ceramic that results in lower material costs without adversely sacrificing the properties obtained with a pure silver formulation. This concept opens the door to a wide range of applications previously prohibited by the much higher cost of Conventional silver conductive.
AA-DUCT CG2 Formulated with Silver coated ceramic power combined with organic binders and solvents to produce electrically conductive paths, films or patterns over non-conductive substrates.
AA-DUCT CG2 formulation produces electrically conductive paths on a wide variety of surfaces including plastics, rubber, cloth, thermoplastic, paper, wood and many others.
AA-DUCT CG2 designed for use in diversified applications as microwave EMI & RFI shielding, in the assembly or repair of printed circuit boards, waveguides, electronic modules, flat cable, static shielding, connections, and circuitry.
- GENERAL INFORMATION:
Appearance: Silver
Coated ceramic %Silver coated ceramic : 76
Cure Type: Heat cure
Benefits:
- High strength
- Perfect bond
- EMI & RFI shielding
- Wave guides
Substrates: Excellent choice for the Integrated Circuits, aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards.
Catalyst: Anhydride
- CURED PROPERTIES:
Sheet Resistivity:
One to One Mix Ratio Electrically Conductive Silver Epoxy For Cold Solder Circuitry, RMI, EFI, PCB, & Electronic Repair 907, 250 gm kit
+ PRODUCT DESCRIPTION:
AA-DUCT 907 is an epoxy adhesive and coating formulation based on pure silver. This versatile silver formulation offers the maximum continuity of conductivity with an electrical resistivity value of less than 1x10-4 ohm•cm.
AA-DUCT 907 is also characterized by a wide operating temperature range from –50 to +170°C. AA-DUCT 907 is recommended for electronic bonding and sealing applications that require both fine electrical and mechanical properties.
+ PRODUCT PROPERTIES:
- Appearance: Silver
- Cure Type: Heat cure or Room temperature
- Benefits:
* High strength
* Perfect bond
* Cold solder for heat-sensitive components
- Mix Ratio by weight 100:100 / Resin:Hardener
- Substrates:
Excellent choice aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards.
- Operating Temperature: –50 to +170°C
- Typical Applications:
Electrical, conductive, rmi/efi shielding, circuitry, printed circuit board and electronics repair
+ UNCURED PROPERTIES:
- Specific Gravity, mixed: 2.79
- Reactive solids contents, %: 100
- Pot Life: 1Hour
- Shelf Life: 6 months
- Viscosity: Paste
+ CURE SCHEDULE:
15 minutes @ 100°C
45 minutes @ 50°C
24 hours @ Room temperature
+ CURED PROPERTIES:
- Hardness, Shore D: 85
- Shrinkage linear in/in: 0.0003
- Lap shear strength, psi: 9400
- Volume Resistivity ohm. cm :< 0.0001
- Thermal Expansion Coefficient, (cm / cm / °C • 10-5): 1.5
- Thermal Conductivity, btu / hr / ft2 / °F / in: 100
- Tensile Strength, psi: 9500
- Compressive Strength, psi: 14,000
- Heat Distortion, °C: 95
- Electrical Resistivity : < 1x10 -4 ohm•cm
+ GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
+ AVAILABILITY:
This epoxy can be supplied in various different packages.
CALL (888) 522-6742 for more informations.
Perfect Bond Silver Epoxy, For Electronic Modules, PCB, Integrated Circuits, Capacitors, Wave Guides & Flat Cables, Electrically Conductive Adhesive,
- PRODUCT DESCRIPTION:
AA-DUCT 2924 is a two part electrically conductive composition developed for low shrinkage; low resistivity bonding applications where good electrical and physical properties over a wide temperature range (up to 190°C) are required.
AA-DUCT 2924 is smooth paste formulation of refined pure silver and epoxy is free of solvents and copper or carbon additives. It can be used -- after REQUIRED high temperature cure cycle -- for the assembly, manufacture and repair of electronic modules, printed circuits, integrated circuits, electrical contacts, capacitors, wave guides and flat cables, for high-frequency RF shielding, and for applications where a "hot" soldering iron is impractical.
When cured AA-DUCT 2924 is a hard, dimensionally stable, conductive material which is resistant to water, weathering, gases and vapors, lubricants, fuels, alcohol, and also to those salts, salt solutions, mild acids and alkalis, and other organic and inorganic compounds with which silver itself is compatible.
- GENERAL PROPERTIES:
Appearance: Silver
Cure Type: Heat cure
Benefits:
+ High strength
+ Perfect bond
+ Mix Ratio by weight: 100:5 / Resin:Hardener
Substrates: Excellent choice aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards.
Operating Temperature: -60 to 190 °C
Shelf Life: 1 Year
- UNCURED PROPERTIES:
Viscosity @ 25 °C cps: Paste
Specific Gravity, mixed: 2.69
Reactive solids contents, %: 100
Pot Life: 3 hours
- CURE SCHEDULE:
2 hours: @ 125 °C
4 hours: @ 100 °C
- MISC PROPERTIES:
Hardness, Shore D: 85
Adhesive bond strength: 1270 psi
Volume Resistivity ohm-cm: < 0.003
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
Call (888) 522-6742 for more information.
High Temperature Adhesive, Fast Cure Epoxy, Low Viscosity For Photographic Industry, Fiber Optics, Laminating, Production & Repair Applications 2 Part
- PRODUCT DESCRIPTION:
AA-BOND F156 is a black, solvent free thixotropic epoxy recommended for high quality photographic industry, laminating, production and repair applications where a room temperature cure optically opaque adhesive for light sensitive components is required.
AA-BOND F156 is two parts smooth paste formulation is easy to use, develops strong bonds to itself and to most materials.
AA-BOND F156 exhibits low shrinkage during cure, has excellent dimensional stability over a wide temperature range.
- GENERAL PROPERTIES:
• Appearance: Black
• Cure Type: Room Temperature or Heat cure
• Benefits:
o Easy to use
o Good low-temperature structural, physical and electrical properties
o It’s resistant to water, weather, gases, salts, mild acids, alkalis, and many organic and inorganic compounds
• Mix Ratio by weight: 100:12 / Resin:Hardener
• Substrates: Glass and glass fabrics, ceramics, leather, metals and many plastics
• Operating Temperature: -60 to 130 °C
• Typical Applications: High quality photographic industry bonding, laminating, production and repair applications where a room-temperature cure optically opaque adhesive for light sensitive components is required.
- UNCURED PROPERTIES:
• Viscosity @ 25 °C, cps 50,000 After mixing
• Specific Gravity, mixed, g/cc 1.57
• Pot life 30 minutes
• Reactive solids contents, % 100
- CURE SCHEDULE:
o 4 hours @ 65°C
o 24 hours @ 25°C
- CURED PROPERTIES:
o Glass transition temperature (Tg), °C 95
o Hardness, Shore D 90
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
CALL (888) 522-6742 for more informations.
Laminating, Sealing & Bonding Applications, Wetting, Great Mechanical & Electrical Properties, Medium Viscosity Epoxy Adhesive Glue 2103, 5gm
- PRODUCT DESCRIPTION:
AA-BOND 2103 is a clear, near transparent, medium viscosity epoxy adhesive formulation developed for rigid laminating, sealing and bonding applications where the combination of good wetting and improved mechanical electrical properties is required. AA-BOND 2103 is two-part liquid epoxy adhesive contains no solvents and is easy to mix, use and apply at room temperature.
AA-BOND 2103 develops strong, rigid, high performance bonds to itself and to ceramics, glass and glass fabrics, metals, laminates and other composite materials, forestry and masonry products, and to most rigid plastics.
AA-BOND 2103 is an effective electrical insulator, and further provides excellent resistance to weather, galvanic action, vapors, JP4 fuel, gasoline, lubricants and other petroleum products, mild acids and alkalis, salts, and other organic and inorganic compounds.
- GENERAL PROPERTIES:
Appearance: Slight haze/Clear
Cure Type: Room temperature or Heat Cure
- Benefits:
Good wetting
Great mechanical properties
Great electrical properties
Solvent free
Easy mix and apply
Mix Ratio by weight 100:25 / Resin:Hardener
- Substrates:
Ceramics, glass to glass, fabrics, metals, laminates and other composite materials
- Operating Temperature: 60 to 125 °C
- UNCURED PROPERTIES:
Specific Gravity 1.2
Reactive solids contents, % 100
Pot Life 20 minutes
- CURE SCHEDULE:
4 hours at 65°C
24 hours at 25°C
- MISC PROPERTIES:
Volume Resistivity 6.00e+13 ohm-cm
Dielectric Constant 4.1Dielectric Strength 420 kV/in
Hardness, Shore D 85
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
600Pcs Cardboard 18650 Battery Insulators Electrical Insulating Adhesive Paper
Features: Outer Ring Diameter: 17mm/ 0.67" (appr. )Inner Ring Diameter: 10mm/ 0.39" (appr. )Thickness: 0.24 mm/ 0.01" (appr. )Package included: 600Pcs Battery Insulators Adhesive Paper (Battery not included) 2 Sheets included, 100 insulators adhesive paper rings per sheet, total is 200 ringsAdhesive cardboard paper for 18650 battery insulator. Better protection to avoid short circuit on batteries. Easy peel and stick application. Package included: 600 x Battery Insulators Adhesive Paper
Clear Epoxy Solvent Free, Low Viscosity, Good Wetting, For Fiber Optic, Electronic, Aerospace, Laminating & Bonding 2113, 5gm
- PRODUCT DESCRIPTION:
AA-BOND 2113 is a clear, low viscosity epoxy adhesive system that contains no solvents, cures at room temperature, has excellent flow ability and wetting characteristics, and adheres strongly to glass, ceramics, most metals and many plastics.
AA-BOND 2113 is particularly recommended for assembly and repair work of fiber optic and other high performance electronic and aerospace systems and components, and for structural laminating applications where an initial low viscosity and near transparent "color" are needed.
AA-BOND 2113 is a good electrical insulator, provides excellent resistance to weather, galvanic action, salt solutions and many other chemicals including mild acid and alkalis, petroleum solvents, lubricating oils, jet fuels and gasoline, and alcohol.
- GENERAL PROPERTIES:
• Appearance Clear transparent
• Cure Type Room temperature or Heat Cure
• Benefits:
o Good wetting
o Solvent free
o Excellent flowability
o Adheres strongly to numerous substrates
• Mix Ratio by weight: 100:11 / Resin:Hardener
• Substrates:
Ceramics, glass to glass, fabrics, metals, laminates and other composite materials
• Operating Temperature: -60 to 130 °C
- UNCURED PROPERTIES:
• Specific Gravity: 1.15
• Reactive solids contents, %: 100
• Pot Life: 30 minutes
- CURE SCHEDULE:
• 4 hours @ 65°C
• 24 hours @ 25°C
- MISC PROPERTIES:
• Volume Resistivity: 6.00e+13 ohm-cm
• Dielectric Constant: 4.2
• Dielectric Strength: 410 volts/mil
• Hardness, Shore D: 88
• Dissipation factor: 0.020
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
- AVAILABILITY:
This epoxy can be supplied in various different packages.
CALL (888) 522-6742 for more information.
FDA Epoxy Class VI Approved 1:1 Mixing For Bonding, Laminating & Repair Applications, Food Preparation, Processing & Packaging Equipment FDA2, 5gm
PRODUCT DESCRIPTION: AA-BOND FDA2 is a medium viscosity epoxy resin system specifically developed for medical device applications. It has been tested in accordance with USP biological reactivity tests, in vivo and received Class VI approval. AA-BOND FDA2 is two part amber adhesive used and cured at room temperature for bonding, laminating and repair applications by manufacturers of food preparation, processing and packaging equipment and devices. AA-BOND FDA2 provides low permeability to gases and vapors, and good resistance to water, weather, petroleum solvents, lubricants, to mild acids and alkalis, and to many other organic and inorganic compounds. GENERAL PROPERTIES: Appearance: Amber Cure Type: Heat cure or Room Temperature Benefits: o Medium viscosity o Class VI approved o Easily mixed o Low permeability o Good resistance Mix Ratio by weight: 100:100 / Resin: Hardener Substrates: Most metals, ceramic, glass and plastics Operating Temperature: -70 to 145 °C Typical Applications: Bonding, laminating and repair applications by manufacturers of food preparation, processing and packaging equipment, and by manufacturers of catheters, hearing aids, dental products and other biomedical instruments and devices. Minimum Service Temperature, Air -94 °F UNCURED PROPERTIES: Viscosity @ 25 °C: 14, 000 ±2000 Specific Gravity, mixed: 1.11 Reactive solids contents, %: 100 Pot Life: 45 minutes CURE SCHEDULE: 1-4 hours @ 65°C 24 hours @ 25°C CURED PROPERTIES: Glass transition temperature (Tg), °C: 54 Hardness, Shore D: 79 Dielectric strength volts/mil: 420 Water Absorption, %:. 004 Lap shear strength, psi: 2700 (Aluminum to Aluminum) GENERAL INFORMATION: For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS). AVAILABILITY: This epoxy can be supplied in various different packages. Call (888) 522-6742 For More Informations.
High Impact Epoxy, Two Part Adhesive, Medium Viscosity, AA-BOND 2135, 5gm kit
This is a medium viscosity epoxy adhesive recommended for bonding, laminating, sealing, and structural repair applications where easy mixing and good wetting combined with high impact strength properties are required. This superior, two-part adhesive is easily mixed and handled at room temperature, and develops strong, tough, high performance bonds to metals, ceramics, wood, concrete, phenolics, polyesters, epoxies, many urethanes and other plastics, and to many other materials. Fully cured this product is a tough, durable, electrically insulating adhesive with excellent mechanical, impact and shock resistance properties. In addition, it provides good resistance to gases, vapors, weather, water, petroleum solvents, anti-icing fluids, salt solutions, many mild acids and alkalis, and many other organic materials. Easy mix pre-measured pouch. Simple mix and use without any mess.
FDA Medical Grade Adhesive, Low Permeability & Viscosity Epoxy, Good Resistance, Electrical Insulator for Bonding & Coating Applications 2 Part, FDA15
- PRODUCT DESCRIPTION:
AA-BOND FDA15 is a low viscosity epoxy resin system specifically developed for bonding and coating applications in accordance with Title 21, U.S. Code of Federal Regulations, Food and Drug Administration Chapter 1, Sub Part B, Sections 175.105 and 175.300.
AA-BOND FDA15 is two-part adhesive is used for bonding, laminating and repair applications by manufacturers of food preparation, processing and packaging equipment, and by manufacturers of catheters, hearing aids, dental products and other biomedical instruments and devices.
AA-BOND FDA15 is an effective electrical insulator, and it provides low permeability to gases and vapors and good resistance to water, weather, galvanic action, to petroleum solvents, lubricants and fuels, to mild acids and alkalis, and to many other organic and inorganic compounds.
- GENERAL PROPERTIES:
• Appearance Clear
• Cure Type Heat cure or Room temperature
• Benefits:
* Low viscosity
* Good resistance
* Effective electrical insulator
* Low permeability
Mix Ratio by weight 100:20 / Resin:Hardener
• Substrates:
* Most metals
* Ceramic
* Glass and plastics
* Operating Temperature -60 to 140 °C.
- Typical Application:
Developed for bonding and coating applications.
- UNCURED PROPERTIES:
Viscosity At 25 °C 4,300 Thixotropic Index 1.0 Specific Gravity, mixed 1.16 g/cc Reactive solids contents, % 100Pot Life 25 minutes.
- CURE SCHEDULE:
• 1-4 hours At 65°C
• 24 hours At 25°C.
- CURED PROPERTIES:
Glass transition temperature (Tg), °C 100 Hardness, Shore D 87Water Absorption, % 0.23Dielectric strength, Volts/mil 420Lap shear strength, psi 2000 (Alum to Alum).
- GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
Call (888) 522-6742 For More Informations.
