Buy Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm in United States - Cartnear.com

Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm

CTNR1070162 CTNR1070162

Atom Adhesives

Atom Adhesives
2025-11-21 USD 41.37

$ 41.37 $ 41.79

Item Added to Cart

*Product availability is subject to suppliers inventory

Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm
SHIPPING ALL OVER UNITED STATES
Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm
100% MONEY BACK GUARANTEE
Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm
EASY 30 DAYSRETURNS & REFUNDS
Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm
24/7 CUSTOMER SUPPORT
Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm
TRUSTED AND SAFE WEBSITE
Pure Silver Conductive Epoxy, Maximum Continuity Of Conductivity For Rear Window Defroster Repair, Grid Repair, Cold Solder, Electronic Bonding, Or Sealing Applications Repair Kit 10gm
100% SECURE CHECKOUT
Brand Atom Adhesives
Model Window Defogger Rep
Type Adhesives
Color/Finish Silver
Window Defroster Grid Repair Kit: The Window Defroster Grid Repair kit is an epoxy adhesive and coating formulation based on pure silver. This versatile silver formulation offers the maximum continuity of conductivity with an electrical resistivity value of less than 1x10-4 ohm.cm. Our Defroster/Window Grid Repair kit is also characterized by a wide operating temperature range from –50 to +170°C. This Defroster/Window Grid Repair kit is recommended for grid repair, electronic bonding, or sealing applications that require both fine electrical and mechanical properties. It can Substrates also aluminum, copper, magnesium, steel, bronze, nickel, kovar, ceramic, glass, phenolic and G-10 epoxy glass boards. Put the measuring lead (Red) and the reference (Black) of the Multimeter on the damaged grid line at both ends, right where the grid connects with the wide bus bars. Move one probe--it doesn't matter which--to the center of the line. If you now read 6 volts, the scratch is not in between the two probes. If you read the same system voltage, 12 volts or so, the break is in between the old probe location and the new one. Just move the probes until you find the location that has full system voltage spanning it. Now it's time to turn off the de¬froster grid and the ignition switch. How To Repair The Defroster Tab: Clean the tab and the contact area with the alcohol prep. Then apply activator to both surfaces and let it dry. Apply the completely mixed adhesive kit to the prepared surfaces, and gently press these surfaces together. Contact pressure is adequate for strong, reliable bonds; however, maintain contact until adhesive is completely cured. Press the tab onto the contact area. Hold it in place until the adhesive sets up, usually about two minutes. Wait 24 hours to use the defogger. Defroster TABS: The tabs located along the sides of the defroster connect the defroster electrically to the vehicles defrost circuit. One tab is the positive and the other ground. If a tab comes off the defroster this will mean total instantaneous failure of the defroster. Our kit is an epoxy adhesive. To use, carefully clean and dry all surfaces to be bonded from all dirt, dust, debris and handprints from the rear window. Apply the completely mixed adhesive kit to the prepared surfaces, and gently press these surfaces together. Contact pressure is adequate for strong, reliable bonds; however, maintain contact until adhesive is completely cured. Some separation of components is common during shipping and storage. For this reason, it is recommended that the contents of the shipping container be thoroughly mixed prior to use. Some ingredients in this formulation provided may crystallize when subjected to low temperature storage. A gentle warming cycle of 52°C for 30 minutes prior to mixing components may be necessary. Crystallized epoxy components do not react as well as liquid components and should be re-dissolved prior to use for best results. Misc Properties: Hardness, Shore D 83 Shrinkage linear in/in 0.003 Lap shear strength, psi 9400 Volume Resistivity ohm cm = 0.0001 Cure Schedule: 2 minutes @ 120°C 5 minutes @ 100°C 12 hours @ 25°C General Properties: Cure Type Heat Cure or Room Temperature Benefits: + High strength + Perfect bond + Cold solder replacement Mix Ratio 100:7 Resin:Hardener - AVAILABILITY: This epoxy can be supplied in various different packages. Call (888) 522-6742 for more information.

Related Products

See More

You May Also Like

See More